silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series sensing and control features ? low cost sensor element ? internal temperature compensation ? differential or gage pressures typical applications ? pneumatic controls ? automotive diagnostics ? medical equipment ? dental equipment ? environmental controls equivalent circuits button, nipple and ?n? packages dip packages warning personal injury do not use these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. failure to comply with these instructions could result in death or serious injury. general description the scc series sensors offer an extremely low cost sensor element with a temperature stable output when driven with a constant current source. these integrated circuit sensors were designed for extremely cost sensitive applications where precise accuracy over a wide temperature range is not required. this series is intended for use with non-corrosive, non-ionic working fluids such as air, and dry gases. absolute devices have an internal vacuum reference and an output voltage proportional to applied pressure. the differential devices allow application of pressure to either side of the diaphragm and devices are thereby available to measure both differential and gage pressures. this product is packaged either in standard low cost chip carrier ?button? package or a dip package. both packages are designed for applications where the sensing element is to be integral to the oem equipment. these packages can be o-ring sealed, epoxied, and/or clamped onto a pressure fitting. a closed bridge four pin sip configuration is provided for electrical connection to the button package. the dip package offers a 5-pin open bridge configuration. warning misuse of documentation ? the information presented in this product sheet is for reference only. do not use this document as a product installation guide. ? complete installation, operation, and maintenance information is provided in the instructions supplied with each product. failure to comply with these instructions could result in death or serious injury.
silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series 2 honeywell ? sensing and control specification characteristics (maximum ratings for all devices) supply current, i s 1.5 ma compensated temperature range 0 c to 50 c [32 f to 122 f] operating temperature range -40 c to 85 c [-40 f to 185 f] storage temperature range -55 c to 125 c [-67 f to 257 f] humidity 0 % to 100 % rh lead temperature 250 c [482 f] soldering 2 sec to 4 sec common-mode pressure 150 psi performance characteristics (individual models) i s =1.0 ma, t a = 25 c [77 f] 1 part number operating pressure range maximum over pressure accuracy 2 effect (3, 4) on span 0 c to 50 c effect (5, 4) on offset 0 c to 50 c full-scale span (6) mv scc05(d,g) 0 psid to 5 psid (g) 20 psi 0.50 % 1.50 % 30 v/c 25-65 scc15a 0 psia to 15 psia 30 psia 0.50 % 1.50 % 40 v/c 40-95 scc15(d,g) 0 psid to 15 psid (g) 30 psi 0.50 % 1.50 % 40 v/c 40-95 scc30(d,g) 0 psid to 30 psid (g) 60 psi 0.50 % 1.50 % 60 v/c 60-150 scc100a 0 psia to 100 psia 150 psia 0.50 % 1.50 % 30 v/c 85-225 scc100(d,g) (7) 0 psig to 100 psig 150 psig 0.50 % 1.50 % 90 v/c 85-225 scc300a 0 psia to 300 psia 450 psia 0.50 % 1.50 % 50 v/c 50-120 performance characteristics (all models) i s =10.0 ma, t a =25 c [77 f] characteristic min. typ. max. unit zero pressure offset (8) -30.0 -10.0 20.0 mv combined linearity, hysteresis and repeatability (2) ? 0.25 0.50 %fso long term stability of offset and span (9) ? 0.10 ? mv response time (10 % to 90 %) (10) ? 0.10 ? ms input impedance 4.00 5.00 6.50 k ? output impedance 4.00 5.00 6.50 k ? specification notes: note 1: reference conditions; supply current = 1.0 ma; t a = 25 c [77 f], common-mode line pressure = 0 psig, pressure applied to p1, unless otherwise noted. note 2: accuracy is the sum of hysteresis and linearity. hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure,. linearity refers to the best straight line fit as measured for the offs et, full-scale and ? full-scale pressure at 25 c [77 f]. note 3: this is the maximum temperature shift for span when measured between 0 c and 50 c [32 f to 122 f] relative to the 25 c [77 f] reading. typical temperature coefficients for span and resistance are -2200 ppm/c and 2200 ppm/c respectively. note 4: temperature effect on span and offset are guaranteed by design. therefore these parameters are not 100 % tested. note 5: this is the maximum temperature shift for offset when measured at 0 c and 50 c [32 f to 122 f] divided by the temperature difference. note 6: span is the algebraic difference between the output voltage at full-scale pressure and the ouput at zero pressure. note 7: the scc100d devices can only be used in a forward gauge mode. application of more than 30 psig to the back side of any of the scc series devices can result in devices failure. on the scc100gd2 pressure can only be applied to the back side of the die. no pressure i accessible from the front/top side of die. note 8: the zero pressure offset is 30 to -20 mv max. form parts sccxxxgd2 and sccxxdd4 devices. note 9: maximum difference in output at any pressure with the operating pressure range and temperature within 0 c and 50 c [32 f to 122 f]. a) 100 temperature cycles, 0 c and 50 c [32 f to 122 f] b) 1.0 million pressure cycles, 0 psi to full-scale span. note 10: response time for a 0 psi to full-scale span pressure step change. 10 % to 90 % rise time.
silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series honeywell ? sensing and control 3 electrical connections ordering information part number for ordering pressure range sensor in button package sensor in ?n? package sensor in nipple package sensor in dip package 0 psid to 5 psid or psig scc05d scc05dn scc05dp1 scc05gd2, scc05dd4 0 psid to 15 psid or psig SCC015D SCC015Dn SCC015Dp1 scc15gd2, scc15dd4 0 psid to 30 psid or psig scc30d scc30dn scc30dp1 scc30gd2, scc30dd4 0 psig to 100 psig scc100d scc100dn ? scc100gd2, scc100dd4 0 psia to 15 psia scc15a scc15an scc15ap1 scc15ad2 0 psia to 30 psia scc30a scc30an scc30ap1 scc30ad2 0 psia to 100 psia scc100a scc100an ? scc100ad2 0 psia to 300 psia ? ? ? ? physical dimensions for reference only mm [in] button package
silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series 4 honeywell ? sensing and control nipple package n housing package
silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series honeywell ? sensing and control 5 d2 dip package dd4 dip package ad4 dip package
silicon pressure sensors 0 psi to 5 psi to 0 psi to 300 psi scc series sensing and control www.honeywell.com/sensing honeywell 11 west spring street freeport, illinois 61032 008135-1-en il50 glo 1004 printed in usa copyright 2004 honeywell international inc. all rights reserved. warranty/remedy honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. contact your local sales office for warranty information. if warranted goods are returned to honeywell during the period of coverage, honeywell will repair or replace without charge those items it finds defective. the foregoing is buyer?s sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. specifications may change without notice. the information we supply is believed to be accurate and reliable as of this printing. however, we assume no responsibility for its use. while we provide application assistance personally, through our literature and the honeywell web site, it is up to the customer to determine the suitability of the product in the application. for application assistance, current specifications, or name of the nearest authorized distributor, contact a nearby sales office. or call: 1-800-537-6945 usa/canada 1-815-235-6847 international fax 1-815-235-6545 usa internet www.honeywell.com/sensing info.sc@honeywell.com
|
